Buckets · Grading and ditching buckets
PSH - hydraulic swivelling grading bucket
- For machines of 12–30 t
- Widths 1,600–2,200 mm
- We usually reply within 1 working day
- We check the fit before we send the quote
- 12 months warranty on manufacturing defects
- Every offer names the dispatch week
- If a bracket we made is wrong and does not fit your machine, we replace it.
Call +48 503 808 636Message us on WhatsAppPhotos and voice notes are welcome.
Standard
Known in Sweden as Planeringsskopa, hydraulisk tilt · in Denmark as Planerskovl, hydraulisk tilt · in Finland as Luiskakauha, hydraulinen kallistus
The whole range: Excavator buckets
- 12–30 tons
- Carriers: Large
The PSH is the hydraulic version of the PS grading bucket. A cylinder swivels the bucket to the side, so the operator sets the angle of the cutting edge from the cab and works a slope without moving the machine.
About this family
The hydraulic version of the PS. A cylinder swivels the bucket, so the cutting edge meets the slope at the angle you set and the machine stays where it is.
The bucket body, the Scandinavian profile and the wear parts are the ones the PS uses. Tell us the machine and the working width and we will quote the right size.
Features
Hydraulic swivel:
- Hydraulic swivel, the cylinder angles the bucket to either side while the machine stays where it is
- Double pilot operated check valve, standard, so the set angle holds under load
- Hydraulic connection on the back of the bucket
Bucket, as on the PS:
- Scandinavian grading profile, low, wide and long, the same body the PS is built on
- Angled sides for visibility and for turning inside a trench
Optional features:
- Back welded cutting edge, optional
- Horizontal wear bars, optional
- Reversible bolt on cutting edge, optional
Typical jobs
The PSH is made for:
- Grading slopes, embankments and verges at a set angle
- Cleaning and shaping ditches from one position on the bank
- Levelling along a wall, a kerb or a pipe run where the machine cannot be moved
- Backfilling and finishing after pipe and cable work
- Landscaping work that has to leave a clean, even surface
Which coupler is on your machine?
Pick the system on your machine and we put it in your enquiry. We check the bracket before we send the quote.
How to measure your coupler
Not sure which system it is? Three measurements tell us which bracket you need.
- Measure the diameter of both pins.
- Measure the distance between the pin centres.
- Measure the width between the inside faces of the ears.
If the coupler has a make or type printed on it, send that too.
- Loading machines…
Models and specifications
The PSH is built on the PS bucket sizes listed here. Weights and capacities for the hydraulic version are to be confirmed.
Datasheet (PDF)- Which bracket does your machine take? See the coupler fit reference
- Looking for your machine by make and model? See the machine fit tables
Column heads: model and Machine class [t] · ✓ marks a width offered for that model
| Width [mm] | PS-16012–16 | PS-19016–19 | PS-23019–23 | PS-30023–30 |
|---|---|---|---|---|
| 1600 | Offered | – | – | – |
| 1800 | Offered | Offered | Offered | Offered |
| 2000 | Offered | Offered | Offered | Offered |
| 2100 | Offered | Offered | Offered | Offered |
| 2200 | Offered | Offered | Offered | Offered |
| Get a price | Get a price | Get a price | Get a price |
→ Scroll the table sideways to see every model.
Compliance, certification & documentation
- EN ISO 3834-2Certified welding qualityCSW/1293/2025
- EN 1090-1 EXC1 + EXC2Factory production control1433-CPR-0257
- EN ISO 9606-1 · WPQR EN ISO 15614Qualified welders and procedures
- EN ISO 9712: VT + PT level 2Non-destructive testingwhere the drawing or inspection plan requires it
- EN 10204 3.1Material traceability
- CE: 2006/42/ECCE markingTransition to Regulation (EU) 2023/1230 underway. Applicable from 20 January 2027.
Warranty
12 months warranty on manufacturing defects in the components Sieruta makes itself.
Normal wear, misuse or overloading and unauthorised modifications are not covered. Warranty terms and claims
Why buy from the factory
- Cutting, machining, welding and painting on one site, our own factory in Poland, EU
- More than 50,000 attachments delivered since 2008
- A record for every serial number, so the spare parts match your attachment
Request a quote
Tell us your machine and the job. An engineer checks the fit, and we usually reply within 1 working day.
More from this family group
Standard
PS - Scandinavian universal / grading bucket
A Scandinavian grading profile, used for grading and levelling.
Fits your machine
Standard
DBF - Flat-top digging bucket for quick coupler
The flat top suits excavators that change attachments on a quick coupler. It comes in Economy, Standard, Heavy Duty and Rock versions.
Fits your machine
Standard
GD - Rigid grading & ditching bucket, 12–40 t
The rigid body has no tilt joint, so there are no hoses or cylinders to connect. It is used to grade surfaces and clean ditches.
Fits your machine
Standard
GDH - Heavy duty hydraulic grading & ditching bucket
The hydraulic tilt grading bucket shapes slopes and levels uneven ground.
Fits your machine
StandardEarthmoving / heavy duty
DB - Heavy duty digging bucket
A digging bucket for most materials, with a rock version for harder ground.
Fits your machine
Standard
SDB - Heavy duty skeleton DB bucket
The SDB separates material as you dig: soil falls through the ribs while stone, rubble and roots stay in the bucket.
Fits your machine
