Attachments for the Liebherr R 960 Demolition Litronic weight range
Price & lead timeGet price & lead time- We usually reply within 1 working day
- We check the fit before we send the quote
- Every offer names the dispatch week
- If a bracket we made is wrong and does not fit your machine, we replace it.
How is the attachment mounted on this machine?
Tell us what is on the machine now. It narrows the sizes we show and goes with your enquiry. It does not confirm fit: we check the bracket before we send the quote.
Special machine configuration (Demolition). Engineering review is required before you select an attachment. Any families shown here are matched by operating weight only.
Price & lead timeGet price & lead timeNo attachment family in our catalogue is listed above 65 t. For a machine of this weight we make the attachment to order: send us the machine details and our engineers reply with an offer.
Which coupler is on your machine?
Pick the system on your machine and we put it in your enquiry. We check the bracket before we send the quote.
How to measure your coupler
Not sure which system it is? Three measurements tell us which bracket you need.
- Measure the diameter of both pins.
- Measure the distance between the pin centres.
- Measure the width between the inside faces of the ears.
If the coupler has a make or type printed on it, send that too.
Before you order: check the interface
The weight class of the Liebherr R 960 Demolition Litronic sizes the attachment. It does not tell you the pin diameter, the pin spacing or the stick width, and those decide whether an attachment fits. Measure them on the machine, or send us the measurements of the bucket it runs today.
Heavy excavators dig rock, load trucks and work in quarries, so wear decides the bucket as much as capacity does. Rock and reinforced buckets carry thicker wear steel, teeth and side cutters, and the bucket is sized to the trucks it loads and to the density of the material.
- Measure the diameter of both bucket pins.
- Measure the distance between the pin centres.
- Measure the inside width between the stick ears.
- If the machine runs a quick coupler, note its make and type.
What these terms mean:
Sizes are matched to the published operating weight of the R 960 Demolition Litronic.
- Weight Class
- Above 65 t: custom build
- Operating Weight
- 77,300 – 97,700 kg
- Family-owned group, founded in 1996
- More than 50,000 attachments delivered
- Built in our own factory in Poland
Operating weight as published by Liebherr, retrieved 2026-09-10. Source
Liebherr R 960 Demolition Litronic: machine data
- Operating weight
- 77,300 – 97,700 kg
- Engine power
- 250 kW
- Maximum digging depth
- 6,750 mm
- Maximum dump height
- 11,800 mm
- Bucket breakout force
- 313 kN
- Arm crowd force
- 248 kN
- Quick coupler
- SWA 66
- Auxiliary circuit flow
- 380 l/min
- Auxiliary circuit pressure
- 350 bar
- Max reach
- 13,650 mmmaker's document (assets-cdn.liebherr.com)
- Arm length
- 2,350–2,900 mmmaker's document (assets-cdn.liebherr.com)
- Main pump flow
- 760 l/minmaker's document (assets-cdn.liebherr.com)
- Bucket capacity
- 2–3 m³maker's document (assets-cdn.liebherr.com)
- Bucket width
- 1,550–2,100 mmmaker's document (assets-cdn.liebherr.com)
- Lift capacity
- 26,400 kgmaker's document (assets-cdn.liebherr.com)
- Transport width
- 3,450 mmmaker's document (assets-cdn.liebherr.com)
As published by Liebherr, retrieved 2026-09-17. Source
What the R 960 Demolition Litronic figures mean for its attachments
- Its auxiliary circuit is rated at 380 l/min and 350 bar. A breaker, auger, tilt rotator or other hydraulic tool states the oil flow it needs, so choose one whose range includes this figure.
- The main pump delivers up to 760 l/min at 350 bar. That is the pump output of the whole machine, not the flow an attachment gets.
- Liebherr lists this quick coupler for it: SWA 66. The bracket on every attachment has to match the coupler.
- It digs down to 6,750 mm. That is the deepest trench it can open.
- Its maximum reach is 13,650 mm.
- It dumps at up to 11,800 mm, so a truck or skip side has to sit below that height.
- Liebherr offers arms from 2,350 to 2,900 mm. A longer arm reaches further, a shorter one handles a heavier bucket.
- Liebherr lists buckets from 1,550 to 2,100 mm wide for this machine.
- Liebherr lists bucket capacities from 2 to 3 m³.
- Bucket breakout force is 313 kN and arm crowd force 248 kN. That is the force a bucket or ripper works with at the tooth.
- Liebherr gives a lifting capacity of 26,400 kg. Check a heavy grab or hammer, plus its load, against the full load chart.
- For transport it measures 14,800 x 3,450 x 3,950 mm (length, width, height).
- Engine power is 250 kW.
Figures as published by Liebherr in its own documents.
How the R 960 Demolition Litronic compares with its neighbours
The nearest models by weight, with the difference to the R 960 Demolition Litronic in parentheses where both makers publish the figure.
| Model | Operating weight | Max dig depth | Main pump flow |
|---|---|---|---|
| R 960 Demolition Litronic | 77.3 t | 6,750 mm | 760 l/min |
| Liebherr R 978 SME Litronic | 78.35 t (+1.05 t) | 7,600 mm (+850) | 820 l/min (+60) |
| Liebherr R 992 Litronic (85,800 – 95,000 kg) | 85.8 t (+8.5 t) | not published | not published |
| Liebherr R 992 Litronic (85,800 – 96,500 kg) | 85.8 t (+8.5 t) | 13,250 mm (+6,500) | 996 l/min (+236) |
| Komatsu PC750SE-6 | 78.3 t (+1 t) | 8,450 mm (+1,700) | 1,008 l/min (+248) |
Figures as each maker publishes them. A difference is shown only where both machines have a published value.
R 960 Demolition Litronic: what the brochure names
Features Liebherr names in its own brochure for the R 960 Demolition Litronic. Some of them may be optional, so check the machine's spec before you order.
- An engine that meets EU Stage V.
- Proportional control of the auxiliary hydraulics, for tilt buckets, augers and breakers.
- A rear or side view camera.
From Liebherr's published brochure. We keep the source document on file.
Other makes of a similar weight
Operating weight within 2 t of the Liebherr R 960 Demolition Litronic.
Why buy from the factory
- Cutting, machining, welding and painting on one site, our own factory in Poland, EU
- More than 50,000 attachments delivered since 2008
- A record for every serial number, so the spare parts match your attachment
Need Custom Specifications?
We can manufacture attachments to your exact pin spacing and requirements for Liebherr R 960 Demolition Litronic.
Welded to EN ISO 3834-2. Agree it as a standing term of supply and the EN 10204 3.1 certificate ships with every attachment. You also get the CE declaration of conformity for every attachment. See the certificates.
Questions about the R 960 Demolition Litronic
- What bucket width fits the R 960 Demolition Litronic?
- Liebherr lists buckets from 1,550 to 2,100 mm wide for it. Pick a width in that range.
- Which quick coupler is installed on your R 960 Demolition Litronic?
- Liebherr lists this coupler for it: SWA 66. Order attachments with the matching bracket.
- Can the R 960 Demolition Litronic run a hydraulic attachment?
- Yes, if the tool's rated range covers the auxiliary circuit: 380 l/min at 350 bar.
Do you sell Liebherr machines? Machine dealer supply
Machine makes and model names belong to their owners. Sieruta is not affiliated with them. We use the names only to show which machines we offer attachments for, by operating weight.