Attachments for the Komatsu PC800LC-8 weight range
Price & lead timeGet price & lead time- We usually reply within 1 working day
- We check the fit before we send the quote
- Every offer names the dispatch week
- If a bracket we made is wrong and does not fit your machine, we replace it.
How is the attachment mounted on this machine?
Tell us what is on the machine now. It narrows the sizes we show and goes with your enquiry. It does not confirm fit: we check the bracket before we send the quote.
No attachment family in our catalogue is listed above 65 t. For a machine of this weight we make the attachment to order: send us the machine details and our engineers reply with an offer.
Which coupler is on your machine?
Pick the system on your machine and we put it in your enquiry. We check the bracket before we send the quote.
How to measure your coupler
Not sure which system it is? Three measurements tell us which bracket you need.
- Measure the diameter of both pins.
- Measure the distance between the pin centres.
- Measure the width between the inside faces of the ears.
If the coupler has a make or type printed on it, send that too.
Before you order: check the interface
The weight class of the Komatsu PC800LC-8 sizes the attachment. It does not tell you the pin diameter, the pin spacing or the stick width, and those decide whether an attachment fits. Measure them on the machine, or send us the measurements of the bucket it runs today.
Heavy excavators dig rock, load trucks and work in quarries, so wear decides the bucket as much as capacity does. Rock and reinforced buckets carry thicker wear steel, teeth and side cutters, and the bucket is sized to the trucks it loads and to the density of the material.
- Measure the diameter of both bucket pins.
- Measure the distance between the pin centres.
- Measure the inside width between the stick ears.
- If the machine runs a quick coupler, note its make and type.
What these terms mean:
Sizes are matched to the published operating weight of the PC800LC-8.
- Weight Class
- Above 65 t: custom build
- Operating Weight
- 78,800 – 84,700 kg
- Family-owned group, founded in 1996
- More than 50,000 attachments delivered
- Built in our own factory in Poland
Operating weight as published by Komatsu, retrieved 2026-09-10. Source
Komatsu PC800LC-8: machine data
- Operating weight
- 78,800 – 84,700 kg
- Engine power
- 370 kW
- Maximum digging depth
- 8,450 mm
- Maximum dump height
- 8,235 mm
- Bucket breakout force
- 397.2 kN
- Arm crowd force
- 326.6 kN
- Auxiliary circuit flow
- 450 l/min
- Max reach
- 13,400 mmmaker's document (komatsu.eu)
- Arm length
- 2,900–3,600 mmmaker's document (komatsu.eu)
- Main pump flow
- 988 l/minmaker's document (komatsu.eu)
- Bucket capacity
- 6.91 m³maker's document (komatsu.eu)
- Lift capacity
- 16,420 kgmaker's document (komatsu.eu)
- Transport width
- 4,335 mmmaker's document (komatsu.eu)
As published by Komatsu, retrieved 2026-09-17. Source
- Pin diameter
- 130 mmSource: Tuff Buckets, Equipment Plus, and Long Reach Boom.Listed for another generation of this model.
A guide only. Measure the pins before you order.
What the PC800LC-8 figures mean for its attachments
- Its auxiliary circuit delivers 450 l/min. A breaker, auger, tilt rotator or other hydraulic tool states the oil flow it needs, so choose one whose range includes this figure.
- The main pump delivers up to 988 l/min at 320 bar. That is the pump output of the whole machine, not the flow an attachment gets.
- It digs down to 8,450 mm. That is the deepest trench it can open.
- Its maximum reach is 13,400 mm.
- It dumps at up to 8,235 mm, so a truck or skip side has to sit below that height.
- Komatsu offers arms from 2,900 to 3,600 mm. A longer arm reaches further, a shorter one handles a heavier bucket.
- Komatsu lists a bucket capacity of 6.91 m³.
- Bucket breakout force is 397.2 kN and arm crowd force 326.6 kN. That is the force a bucket or ripper works with at the tooth.
- Komatsu gives a lifting capacity of 16,420 kg. Check a heavy grab or hammer, plus its load, against the full load chart.
- Its transport width is 4,335 mm.
- Engine power is 370 kW.
Figures as published by Komatsu in its own documents.
How the PC800LC-8 compares with its neighbours
The nearest models by weight, with the difference to the PC800LC-8 in parentheses where both makers publish the figure.
| Model | Operating weight | Max dig depth | Main pump flow |
|---|---|---|---|
| PC800LC-8 | 78.8 t | 8,450 mm | 988 l/min |
| Komatsu PC750SE-6 | 78.3 t (-0.5 t) | 8,450 mm | 1,008 l/min (+20) |
| Komatsu PC750LC-7 | 80.6 t (+1.8 t) | 8,450 mm | 988 l/min |
| Sany SY750H | 78.5 t (-0.3 t) | 7,580 mm (-870) | 1,008 l/min (+20) |
Figures as each maker publishes them. A difference is shown only where both machines have a published value.
PC800LC-8: build years and variants
Build years: 2008–2018
Variants
- PC800LC-8 E0 (2008–2018)
Years and variants as listed in the LECTURA Specs database.
PC800LC-8: what the brochure names
Features Komatsu names in its own brochure for the PC800LC-8. Some of them may be optional, so check the machine's spec before you order.
- Work modes you select from the cab.
- A rear or side view camera.
- A load-sensing hydraulic system.
- Operator protection certified to ROPS and FOPS.
From Komatsu's published brochure. We keep the source document on file.
Other Komatsu models of a similar weight
Other makes of a similar weight
Operating weight within 2 t of the Komatsu PC800LC-8.
Why buy from the factory
- Cutting, machining, welding and painting on one site, our own factory in Poland, EU
- More than 50,000 attachments delivered since 2008
- A record for every serial number, so the spare parts match your attachment
Need Custom Specifications?
We can manufacture attachments to your exact pin spacing and requirements for Komatsu PC800LC-8.
Welded to EN ISO 3834-2. Agree it as a standing term of supply and the EN 10204 3.1 certificate ships with every attachment. You also get the CE declaration of conformity for every attachment. See the certificates.
Questions about the PC800LC-8
- What bucket size fits the PC800LC-8?
- Komatsu lists a bucket capacity of 6.91 m³ for it.
- Can the PC800LC-8 run a hydraulic attachment?
- Yes, if the tool's rated oil flow range includes the 450 l/min of its auxiliary circuit.
Do you sell Komatsu machines? Machine dealer supply
Machine makes and model names belong to their owners. Sieruta is not affiliated with them. We use the names only to show which machines we offer attachments for, by operating weight.