Attachments for the Sany SY750H weight range
Price & lead timeGet price & lead time- We usually reply within 1 working day
- We check the fit before we send the quote
- Every offer names the dispatch week
- If a bracket we made is wrong and does not fit your machine, we replace it.
How is the attachment mounted on this machine?
Tell us what is on the machine now. It narrows the sizes we show and goes with your enquiry. It does not confirm fit: we check the bracket before we send the quote.
No attachment family in our catalogue is listed above 65 t. For a machine of this weight we make the attachment to order: send us the machine details and our engineers reply with an offer.
Which coupler is on your machine?
Pick the system on your machine and we put it in your enquiry. We check the bracket before we send the quote.
How to measure your coupler
Not sure which system it is? Three measurements tell us which bracket you need.
- Measure the diameter of both pins.
- Measure the distance between the pin centres.
- Measure the width between the inside faces of the ears.
If the coupler has a make or type printed on it, send that too.
Before you order: check the interface
The weight class of the Sany SY750H sizes the attachment. It does not tell you the pin diameter, the pin spacing or the stick width, and those decide whether an attachment fits. Measure them on the machine, or send us the measurements of the bucket it runs today.
Heavy excavators dig rock, load trucks and work in quarries, so wear decides the bucket as much as capacity does. Rock and reinforced buckets carry thicker wear steel, teeth and side cutters, and the bucket is sized to the trucks it loads and to the density of the material.DBS - engineered rock bucket for excavator
- Measure the diameter of both bucket pins.
- Measure the distance between the pin centres.
- Measure the inside width between the stick ears.
- If the machine runs a quick coupler, note its make and type.
What these terms mean:
Sizes are matched to the published operating weight of the SY750H.
- Weight Class
- Above 65 t: custom build
- Operating Weight
- 78,500 kg
- Family-owned group, founded in 1996
- More than 50,000 attachments delivered
- Built in our own factory in Poland
Operating weight as published by Sany, retrieved 2026-09-11. Source
Sany SY750H: machine data
- Operating weight
- 78,500 kg
- Engine power
- 391 kW
- Maximum digging depth
- 7,580 mm
- Maximum dump height
- 7,170 mm
- Bucket breakout force
- 410 kN
- Arm crowd force
- 354 kN
- Quick coupler
- Quick coupler
- Max reach
- 12,100 mmmaker's document (sanyeurope.com)
- Arm length
- 3,000–3,600 mmmaker's document (sanyeurope.com)
- Main pump flow
- 1,008 l/minmaker's document (sanyeurope.com)
- Bucket capacity
- 5 m³maker's document (sanyeurope.com)
- Transport width
- 4,030 mmmaker's document (sanyeurope.com)
As published by Sany, retrieved 2026-09-19. Source
What the SY750H figures mean for its attachments
- The main pump delivers up to 1,008 l/min at 343 bar. That is the pump output of the whole machine, not the flow an attachment gets.
- Sany lists this quick coupler for it: Quick coupler. The bracket on every attachment has to match the coupler.document from sanyamerica.com
- It digs down to 7,580 mm. That is the deepest trench it can open.
- Its maximum reach is 12,100 mm.
- It dumps at up to 7,170 mm, so a truck or skip side has to sit below that height.
- Sany offers arms from 3,000 to 3,600 mm. A longer arm reaches further, a shorter one handles a heavier bucket.
- Sany lists a bucket capacity of 5 m³.
- Bucket breakout force is 410 kN and arm crowd force 354 kN. That is the force a bucket or ripper works with at the tooth.
- For transport it measures 12,879 x 4,030 x 4,981 mm (length, width, height).
- Engine power is 391 kW.
Figures without a source note are as published by Sany in its own documents.
How the SY750H compares with its neighbours
The nearest models by weight, with the difference to the SY750H in parentheses where both makers publish the figure.
| Model | Operating weight | Max dig depth | Main pump flow |
|---|---|---|---|
| SY750H | 78.5 t | 7,580 mm | 1,008 l/min |
| Sany SY500HRD | 64 t (-14.5 t) | not published | 720 l/min (-288) |
| Sany SY980H | 95 t (+16.5 t) | 7,062 mm (-518) | 1,130 l/min (+122) |
| Liebherr R 978 SME Litronic | 78.35 t (-0.15 t) | 7,600 mm (+20) | 820 l/min (-188) |
Figures as each maker publishes them. A difference is shown only where both machines have a published value.
SY750H: build years and variants
Build years: 2018–2026
Variants
- SY750H (2018–2026)
Years and variants as listed in the LECTURA Specs database.
Other Sany models of a similar weight
Other makes of a similar weight
Operating weight within 2 t of the Sany SY750H.
Why buy from the factory
- Cutting, machining, welding and painting on one site, our own factory in Poland, EU
- More than 50,000 attachments delivered since 2008
- A record for every serial number, so the spare parts match your attachment
Need Custom Specifications?
We can manufacture attachments to your exact pin spacing and requirements for Sany SY750H.
Welded to EN ISO 3834-2. Agree it as a standing term of supply and the EN 10204 3.1 certificate ships with every attachment. You also get the CE declaration of conformity for every attachment. See the certificates.
Questions about the SY750H
- What bucket size fits the SY750H?
- Sany lists a bucket capacity of 5 m³ for it.
- Which quick coupler is installed on your SY750H?
- Sany lists this coupler for it: Quick coupler. Order attachments with the matching bracket.
Do you sell Sany machines? Machine dealer supply
Machine makes and model names belong to their owners. Sieruta is not affiliated with them. We use the names only to show which machines we offer attachments for, by operating weight.