Attachments for the Hitachi ZX890-7G weight range
Price & lead timeGet price & lead time- We usually reply within 1 working day
- We check the fit before we send the quote
- Every offer names the dispatch week
- If a bracket we made is wrong and does not fit your machine, we replace it.
How is the attachment mounted on this machine?
Tell us what is on the machine now. It narrows the sizes we show and goes with your enquiry. It does not confirm fit: we check the bracket before we send the quote.
These machines weigh more than 80 t, the limit of what we build to order. Send us the machine details and we tell you what we can build.
Which coupler is on your machine?
Pick the system on your machine and we put it in your enquiry. We check the bracket before we send the quote.
How to measure your coupler
Not sure which system it is? Three measurements tell us which bracket you need.
- Measure the diameter of both pins.
- Measure the distance between the pin centres.
- Measure the width between the inside faces of the ears.
If the coupler has a make or type printed on it, send that too.
Before you order: check the interface
The weight class of the Hitachi ZX890-7G sizes the attachment. It does not tell you the pin diameter, the pin spacing or the stick width, and those decide whether an attachment fits. Measure them on the machine, or send us the measurements of the bucket it runs today.
Heavy excavators dig rock, load trucks and work in quarries, so wear decides the bucket as much as capacity does. Rock and reinforced buckets carry thicker wear steel, teeth and side cutters, and the bucket is sized to the trucks it loads and to the density of the material.
- Measure the diameter of both bucket pins.
- Measure the distance between the pin centres.
- Measure the inside width between the stick ears.
- If the machine runs a quick coupler, note its make and type.
What these terms mean:
Sizes are matched to the published operating weight of the ZX890-7G.
- Weight Class
- Above our standard range: custom build, ask us
- Operating Weight
- 81,700 – 85,300 kg
- Family-owned group, founded in 1996
- More than 50,000 attachments delivered
- Built in our own factory in Poland
Operating weight as published by Hitachi, retrieved 2026-09-10. Source
Hitachi ZX890-7G: machine data
- Operating weight
- 81,700 – 85,300 kg
- Engine power
- 377 kW
- Maximum digging depth
- 8,870 mm
- Maximum dump height
- 9,080 mm
- Max reach
- 13,820 mmmaker's document (hitachicm.com)
- Arm length
- 2,950–3,700 mmmaker's document (hitachicm.com)
- Main pump flow
- 1,024 l/minmaker's document (hitachicm.com)
- Bucket capacity
- 2.9–5 m³maker's document (hitachicm.com)
- Bucket width
- 1,590–2,260 mmmaker's document (hitachicm.com)
- Lift capacity
- 26,200 kgmaker's document (hitachicm.com)
- Transport width
- 4,450 mmmaker's document (hitachicm.com)
As published by Hitachi, retrieved 2026-09-19. Source
What the ZX890-7G figures mean for its attachments
- The main pump delivers up to 1,024 l/min at 319 bar. That is the pump output of the whole machine, not the flow an attachment gets.
- It digs down to 8,870 mm. That is the deepest trench it can open.
- Its maximum reach is 13,820 mm.
- It dumps at up to 9,080 mm, so a truck or skip side has to sit below that height.
- Hitachi offers arms from 2,950 to 3,700 mm. A longer arm reaches further, a shorter one handles a heavier bucket.
- Hitachi lists buckets from 1,590 to 2,260 mm wide for this machine.
- Hitachi lists bucket capacities from 2.9 to 5 m³.
- Hitachi gives a lifting capacity of 26,200 kg. Check a heavy grab or hammer, plus its load, against the full load chart.
- For transport it measures 14,800 x 4,450 x 4,770 mm (length, width, height).
- Engine power is 377 kW.
Figures as published by Hitachi in its own documents.
How the ZX890-7G compares with its neighbours
The nearest models by weight, with the difference to the ZX890-7G in parentheses where both makers publish the figure.
| Model | Operating weight | Max dig depth | Main pump flow |
|---|---|---|---|
| ZX890-7G | 81.7 t | 8,870 mm | 1,024 l/min |
| Hitachi ZX890LCH-7 / ZX890LCR-7 | 84.6 t (+2.9 t) | 8,870 mm | 1,112 l/min (+88) |
| Hitachi ZX600MC-7 | 69.4 t (-12.3 t) | not published | 770 l/min (-254) |
| Kobelco SK850LC-11 | 81.8 t (+0.1 t) | 10,700 mm (+1,830) | 1,008 l/min (-16) |
Figures as each maker publishes them. A difference is shown only where both machines have a published value.
ZX890-7G: what the brochure names
Features Hitachi names in its own brochure for the ZX890-7G. Some of them may be optional, so check the machine's spec before you order.
- Work modes you select from the cab.
- Operator protection certified to ROPS and FOPS.
- Telematics for tracking the machine remotely (ConSite).
- A rear or side view camera.
From Hitachi's published brochure. We keep the source document on file.
Other makes of a similar weight
Operating weight within 2 t of the Hitachi ZX890-7G.
Why buy from the factory
- Cutting, machining, welding and painting on one site, our own factory in Poland, EU
- More than 50,000 attachments delivered since 2008
- A record for every serial number, so the spare parts match your attachment
Need Custom Specifications?
We can manufacture attachments to your exact pin spacing and requirements for Hitachi ZX890-7G.
Welded to EN ISO 3834-2. Agree it as a standing term of supply and the EN 10204 3.1 certificate ships with every attachment. You also get the CE declaration of conformity for every attachment. See the certificates.
Questions about the ZX890-7G
- What bucket width fits the ZX890-7G?
- Hitachi lists buckets from 1,590 to 2,260 mm wide for it. Pick a width in that range.
Do you sell Hitachi machines? Machine dealer supply
Machine makes and model names belong to their owners. Sieruta is not affiliated with them. We use the names only to show which machines we offer attachments for, by operating weight.