Attachments for the Kobelco SK850LC-11 weight range
Price & lead timeGet price & lead time- We usually reply within 1 working day
- We check the fit before we send the quote
- Every offer names the dispatch week
- If a bracket we made is wrong and does not fit your machine, we replace it.
How is the attachment mounted on this machine?
Tell us what is on the machine now. It narrows the sizes we show and goes with your enquiry. It does not confirm fit: we check the bracket before we send the quote.
These machines weigh more than 80 t, the limit of what we build to order. Send us the machine details and we tell you what we can build.
Which coupler is on your machine?
Pick the system on your machine and we put it in your enquiry. We check the bracket before we send the quote.
How to measure your coupler
Not sure which system it is? Three measurements tell us which bracket you need.
- Measure the diameter of both pins.
- Measure the distance between the pin centres.
- Measure the width between the inside faces of the ears.
If the coupler has a make or type printed on it, send that too.
Before you order: check the interface
The weight class of the Kobelco SK850LC-11 sizes the attachment. It does not tell you the pin diameter, the pin spacing or the stick width, and those decide whether an attachment fits. Measure them on the machine, or send us the measurements of the bucket it runs today.
Heavy excavators dig rock, load trucks and work in quarries, so wear decides the bucket as much as capacity does. Rock and reinforced buckets carry thicker wear steel, teeth and side cutters, and the bucket is sized to the trucks it loads and to the density of the material.
- Measure the diameter of both bucket pins.
- Measure the distance between the pin centres.
- Measure the inside width between the stick ears.
- If the machine runs a quick coupler, note its make and type.
What these terms mean:
Sizes are matched to the published operating weight of the SK850LC-11.
- Weight Class
- Above our standard range: custom build, ask us
- Operating Weight
- 81,800 – 81,900 kg
- Family-owned group, founded in 1996
- More than 50,000 attachments delivered
- Built in our own factory in Poland
Operating weight as published by Kobelco, retrieved 2026-09-10. Source
Kobelco SK850LC-11: machine data
- Operating weight
- 81,800 – 81,900 kg
- Engine power
- 382 kW
- Maximum digging depth
- 10,700 mm
- Maximum dump height
- 8,870 mm
- Bucket breakout force
- 403 kN
- Arm crowd force
- 234 kN
- Tail swing radius
- 4,580 mm
- Max reach
- 15,230 mmmaker's document (kobelco-europe.com)
- Arm length
- 2,900–5,400 mmmaker's document (kobelco-europe.com)
- Main pump flow
- 1,008 l/minmaker's document (kobelco-europe.com)
- Bucket capacity
- 2.3–5.4 m³maker's document (kobelco-europe.com)
- Bucket width
- 1,370–2,500 mmmaker's document (kobelco-europe.com)
- Lift capacity
- 30,390 kgmaker's document (kobelco-europe.com)
- Transport width
- 3,640 mmmaker's document (kobelco-europe.com)
As published by Kobelco, retrieved 2026-09-18. Source
- Pin diameter
- 25 mmSource: Tuff Buckets.Listed for another generation of this model.
A guide only. Measure the pins before you order.
What the SK850LC-11 figures mean for its attachments
- The main pump delivers up to 1,008 l/min at 330 bar. That is the pump output of the whole machine, not the flow an attachment gets.
- It digs down to 10,700 mm. That is the deepest trench it can open.
- Its maximum reach is 15,230 mm.
- It dumps at up to 8,870 mm, so a truck or skip side has to sit below that height.
- Kobelco offers arms from 2,900 to 5,400 mm. A longer arm reaches further, a shorter one handles a heavier bucket.
- Kobelco lists buckets from 1,370 to 2,500 mm wide for this machine.
- Kobelco lists bucket capacities from 2.3 to 5.4 m³.
- Bucket breakout force is 403 kN and arm crowd force 234 kN. That is the force a bucket or ripper works with at the tooth.
- Kobelco gives a lifting capacity of 30,390 kg. Check a heavy grab or hammer, plus its load, against the full load chart.
- Its tail swing radius is 4,580 mm, which matters beside a wall or in a live traffic lane.
- For transport it measures 14,530 x 3,640 x 4,790 mm (length, width, height).
- Engine power is 382 kW.
Figures as published by Kobelco in its own documents.
How the SK850LC-11 compares with its neighbours
The nearest models by weight, with the difference to the SK850LC-11 in parentheses where both makers publish the figure.
| Model | Operating weight | Max dig depth | Main pump flow |
|---|---|---|---|
| SK850LC-11 | 81.8 t | 10,700 mm | 1,008 l/min |
| Kobelco SK850LC | 80.5 t (-1.3 t) | 7,380 mm (-3,320) | 1,008 l/min |
| Kobelco SK650DLC-11 | 76.2 t (-5.6 t) | not published | 740 l/min (-268) |
| Hitachi ZX890-7G | 81.7 t (-0.1 t) | 8,870 mm (-1,830) | 1,024 l/min (+16) |
Figures as each maker publishes them. A difference is shown only where both machines have a published value.
SK850LC-11: what the brochure names
Features Kobelco names in its own brochure for the SK850LC-11. Some of them may be optional, so check the machine's spec before you order.
- An engine that meets EU Stage V.
- Automatic engine idle when the controls are left alone.
- Work modes you select from the cab.
- A long arm.
From Kobelco's published brochure. We keep the source document on file.
Other Kobelco models of a similar weight
Other makes of a similar weight
Operating weight within 2 t of the Kobelco SK850LC-11.
Why buy from the factory
- Cutting, machining, welding and painting on one site, our own factory in Poland, EU
- More than 50,000 attachments delivered since 2008
- A record for every serial number, so the spare parts match your attachment
Need Custom Specifications?
We can manufacture attachments to your exact pin spacing and requirements for Kobelco SK850LC-11.
Welded to EN ISO 3834-2. Agree it as a standing term of supply and the EN 10204 3.1 certificate ships with every attachment. You also get the CE declaration of conformity for every attachment. See the certificates.
Questions about the SK850LC-11
- What bucket width fits the SK850LC-11?
- Kobelco lists buckets from 1,370 to 2,500 mm wide for it. Pick a width in that range.
Do you sell Kobelco machines? Machine dealer supply
Machine makes and model names belong to their owners. Sieruta is not affiliated with them. We use the names only to show which machines we offer attachments for, by operating weight.