Application
Earthmoving
Buckets and rippers for digging and moving soil in bulk.
Standard
AC mini - asphalt cutter for mini-excavator
Asphalt cutter for mini-excavators. The 450 mm steel disc cuts asphalt for roadworks, repairs and utility trenches.
Fits your machine
Standard
BDP mini - clay digging bucket for mini-excavator
The BDP bucket has the narrow Dutch profile for sticky clay and rocky ground on mini and midi-excavators. Anti-suction holes are an option, so sticky clay does not hold to the bucket floor.
Fits your machine
Standard
CB - heavy duty hydraulic clamp bucket
A hydraulic clamp arm closes onto the load, and a double pilot check valve holds it shut if a hose fails. The excavator digs, then picks up rubble, stumps, pipes and awkward stone.
Fits your machine
Standard
CB mini - hydraulic clamp bucket for mini-excavator
The hydraulic clamp bucket lets an excavator dig, then its clamp grips material for handling and sorting.
Fits your machine
StandardEarthmoving / heavy duty
DB - heavy duty digging bucket
A digging bucket for most materials, with a rock version for harder ground.
Fits your machine
Standard
DBF - flat-top digging bucket for quick coupler
The flat top suits excavators that change attachments on a quick coupler. It comes in Economy, Standard, Heavy Duty and Rock versions.
Fits your machine
Standard
DCB - grading & ditching bucket with round profile
The round profile lets material flow out with little drag. Use it to grade surfaces and to dig and clean ditches.
Fits your machine
Standard
DSX - Nordic heavy duty digging bucket
Nordic profile heavy duty digging bucket for excavators from 14 to 40 t, made of Hardox® 450 for rocky ground.
Fits your machine
Standard
DS mini - Scandinavian deep digging bucket for mini-excavator
Deep digging bucket in the Nordic profile for mini-excavators, for rocky ground and abrasive material.
Fits your machine
Standard
DuoRIP - double ripper for root extraction
Two shanks go deep into the ground at once. It rips out root systems, large roots and stumps when land is cleared for a site.
Fits your machine
Standard
FGP - general purpose loader bucket
General purpose bucket for a front loader, for loading, unloading and stockpiling loose material.
Fits your machine
Standard
FLB - levelling bucket for front loader
Wide, low levelling bucket for a front loader, made for fine grading.
Fits your machine
Standard
GB - rigid grading & ditching bucket, German profile
Rigid grading & ditching bucket with a flat top. It is used for ditch cleaning, grading and slope work.
Fits your machine
Standard
GBH - hydraulic tilt ditching bucket for mini-excavator
Tilts up to 45 degrees to each side, and double pilot check valves hold the angle. Slopes, ditches and banks are shaped without moving the machine.
Fits your machine
Standard
GBP - rigid grading & ditching bucket, Italian profile
A rigid grading and ditching bucket with a round inner profile and an HB500 cutting edge. It cleans ditches, grades and cuts slopes on mini and midi excavators.
Fits your machine
Standard
GBPH - hydraulic tilting grading & ditching bucket
Tilts 45 degrees to each side, and a double pilot check valve holds the angle. Ditches, slopes and banks are cleaned and shaped without moving the mini-excavator.
Fits your machine
Standard
GD - rigid grading & ditching bucket, 12–40 t
The rigid body has no tilt joint, so there are no hoses or cylinders to connect. It is used to grade surfaces and clean ditches.
Fits your machine
Standard
GDH - heavy duty hydraulic grading & ditching bucket
The hydraulic tilt grading bucket shapes slopes and levels uneven ground.
Fits your machine
Standard
GKB mini - deep cable digging bucket for mini-excavator
The GKB Deep Cable Bucket lets a mini-excavator dig deep trenches for cables. It works in hard ground.
Fits your machine
Standard
GP - general purpose digging bucket
A digging bucket for everyday excavation in earth, gravel, and loose materials. It is used for trenching, foundation work, and landscaping.
Fits your machine
Standard
GPL - general purpose digging bucket
A bucket for digging common materials like earth, gravel, and loose soil. It is used for trenching, foundation work, and landscaping.
Fits your machine
Standard
GPLO - GPL bucket with perforated bottom
The bottom plate has holes cut in it, so fine soil, sand and water fall through while stones and roots stay in. You dig and screen in the same pass.
Fits your machine
Standard
GPO - GP bucket with perforated bottom
Holes cut in the bottom let soil fall through while stones stay in the bucket. A mini or midi excavator sorts stone from soil as it digs.
Fits your machine
Standard
GRB - excavator grading beam
A grading beam for excavators from 6 to 30 t. It levels large areas for driveways, roads and building sites.
Fits your machine
Standard
GRB light - mini-excavator grading beam with lowered mass
A grading beam for mini excavators from 0.6 to 7.0 t. It levels the ground for driveways, roads and building pads.
Fits your machine
Standard
LR mini - straight land rakes for mini-excavator
Tines instead of a solid shell pull out roots, brush and stones while the soil falls back through. A plot is cleared before levelling without carting away the topsoil.
Fits your machine
Standard
LRS - short land rakes for mini-excavators
A shorter, narrower land rake for small machines working in tight plots and along boundaries. It pulls out roots and stones and lets the soil fall through.
Fits your machine
Standard
MR - heavy duty excavator multi-ripper
The MR multi-ripper enters the ground on several legs at once and breaks up and loosens compacted material.
Fits your machine
Standard
MR mini - multi-ripper for mini-excavator
Multi-rippers for mini-excavators break up hard soil and debris when you prepare a site.
Fits your machine
Standard
PDP mini - skeleton BDP stone bucket
Skeleton bucket for mini and midi excavators, built heavier than a general-purpose bucket. It sieves on site and handles demolition, excavation and loading.
Fits your machine
Standard
PS mini - Scandinavian universal grading bucket for mini-excavator
The PS mini grading bucket has the Scandinavian profile. It is made for mini-excavators, for fine grading and finishing work.
Fits your machine
Standard
PS - Scandinavian universal / grading bucket
A Scandinavian grading profile, used for grading and levelling.
Fits your machine
Standard
RDBF - flat-top skeleton DBF bucket on rods
Interlocking steel rods replace the solid bottom, C45 as standard and Hardox® as an option. Soil sifts out from the rocks while you dig trenches, drains and pipe bedding.
Fits your machine
Standard
RGP - skeleton rod GP bucket
Parallel Hardox® rods in the universal GP profile let fine material fall through and keep the oversize in the bucket. Screening, loading and sorting happen in one movement.
Fits your machine
Standard
RGPL - skeleton rod GPL bucket
Built on the GPL bucket, with a bent top section for digging and a recessed bracket as an option. A mini-excavator separates material and cleans up with it.
Fits your machine
Standard
RGPR - skeleton rod bucket
In the RGPR a bottom of C45 steel rods lets soil and water fall through, while stones, roots and rubble stay in the bucket. Material is sorted as it is dug.
Fits your machine
Standard
RIP - heavy duty ripper
A single shank made of high-strength steel, with a protector over the shank. It breaks up hard soil, rock and frozen ground, so the material can then be loaded with an ordinary digging bucket.
Fits your machine
Standard
RIP mini - ripper shank for mini-excavator
Mini-excavator rippers break up hard ground before trenching and foundation work.
Fits your machine
Standard
SB mini - Dutch profile grading & ditching bucket for mini-excavator
Dutch profile grading and ditching bucket for mini-excavators. It is used for grading, cleaning ditches and cutting slopes.
Fits your machine
Standard
SB - Dutch profile grading & ditching bucket
The Dutch profile has a wider opening, so sticky soil falls out. Use it for grading and ditch work in sticky soil.
Fits your machine
Standard
SDB - heavy duty skeleton DB bucket
The SDB separates material as you dig: soil falls through the ribs while stone, rubble and roots stay in the bucket.
Fits your machine
Standard
SGP - heavy duty skeleton GP bucket
Built on the GP bucket, with a bottom of S355 steel ribs instead of a closed plate. Fine soil and water fall through, and stones, roots and rubble stay in the bucket.
Fits your machine
Standard
SGPL - heavy duty skeleton GPL bucket for mini-excavator
Built on the GPL bucket, with S355 steel ribs in the bottom instead of a closed plate. A mini or midi excavator separates fine soil and water from stones, roots and rubble in the same pass.
Fits your machine
Configured
TR - trapezoid profile digging bucket
The sloped side walls form the ditch section in a single pass, so drainage channels and utility ditches need no follow-up trimming.
Fits your machine
Configured
UB - U-shape digging bucket
The bucket cuts a U-shaped trench bottom to profile in one pass. Pipe laying and utility work need less backfilling, less handwork and less spoil hauled away.
Fits your machine
Configured
VB - V-shape digging bucket
The bucket angle is made to your slope. It cuts a V-shaped ditch or slope in one pass for drainage channels, swales and road shoulders.
Fits your machine
How to choose
Work through these questions in order, from the ground to the machine.
- 1
Can a bucket get into the ground?
If it cannot, rip it first and load it afterwards with a digging bucket. The RIP opens compacted soil, frost, hard clay, soft rock and old surfaces with one shank. The MR breaks the ground with five teeth at once, so one pass loosens a wider strip and leaves smaller lumps to load. On a mini excavator, the RIP mini opens frozen ground, compacted clay and stony fill, and the MR mini breaks compacted soil, frozen layers and root networks.
- 2
What are you digging?
Loose earth, sand, gravel and firm clay: a general purpose bucket digs, ditches and loads it. Take the GP or GPL on a mini or midi excavator and the DB on a full size excavator. Sticky clay and wet soil: the BDP mini has a narrow Dutch profile, so the bucket cuts in and the material falls out when it is emptied. Anti-suction holes are an option.
- 3
How deep is the cut?
The DS mini has a longer bottom and a larger tip radius than a normal digging bucket. It digs deeper in one pass, so the machine has to be moved less often, and the long bottom holds large stones and stony soil in the bucket.
- 4
Is the soil stony or abrasive?
To sort stones out as you dig, use a bucket with an open bottom. On the GPO and GPLO the bottom plate has holes cut in it, and on the SGP a row of S355 steel ribs replaces the solid plate. Fine soil falls through and the stones stay in the bucket. For rocky and abrasive ground, the DB and DBF come in a rock version, and the DSX body is Hardox® 450 steel.
- 5
How does the bucket go on the machine?
If you change attachments on a quick coupler, take the DBF, the flat-top digging bucket made for it, in Economy up to 24 t, Standard, and Heavy Duty from 24 t. The GP, GPL and DS mini are made with a direct OEM hitch or for your quick coupler, for example MS, Martin, HydroQuick or CW, or with an S-System mount. The DB fits directly or on SW and CW adapters.
- 6
Which machine carries it?
Match the bucket to the machine weight: GP, GPL and DS mini from 0.6 to 10 t, BDP mini, GPO and SGP from 1.2 to 10 t, DB and DBF from 10 to 50 t, DSX from 14 to 40 t, MR from 11 to 32 t, RIP from 14 to 65 t. The DB, DBF, DSX and MR take any major tooth system, for example CAT J, ESCO, BYG, MTG or Combi Wear Parts. On a wheel loader, the FGP loads and carries loose material and handles light earthmoving and site cleanup, on loaders from 2 to 6 t and from 12 to 24 t.
Attachments by job
Pick the bucket for the soil first, then add a ripper where the bucket cannot go.
Loose earth, sand, gravel and firm clay
A general purpose bucket digs and loads it. GP or GPL on a mini or midi excavator, DB on a full size excavator.
Sticky clay and wet soil
The BDP mini has a narrow Dutch profile made for sticky clay and wet soil.
Deeper cuts
The DS mini has a longer bottom and a larger tip radius, so it cuts deeper in one pass.
Ground a bucket cannot enter
A ripper opens it first. RIP with one shank, MR with five legs for a wider strip. RIP mini and MR mini on a mini excavator.
Loading with a wheel loader
The FGP loads and carries loose material and handles light digging and site cleanup.
Need a price for Earthmoving attachments?
Tell us the machine and the attachment you need. We usually reply within 1 working day.